Butterfly Valve Electric Wafer Lug Type Eccentric DN16

Product Description:

1. Manual Wafer Butterfly Valve Description：
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. A butterfly valve consists of body ,stem ,disc , actuator (manual actuator, worm-gear actuator , aerodynamic actuator or electric actuator) , and wafer type butterfly valve can implement the process for turning on turning off and regulating the flow by the circumrotation of stem and disc  that is droved by actuators.
The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Butterfly Valve

1. Wide selection of materials, applicable to various mediums
2. The material of valve body: cast iron, cast steel, cast stainless steel and so on.
3. Pressure grade: 1.6Mpa, 4.0Mpa, 6.4Mpa
4. Connecting type: flange coupling
5. Temperature range: normal temperature -20---230ºC  the thermal slug type -60---450ºC
6. Operation form: automatic open or close
7. Flow characteristic: equal percentage, linearity
8. Leakage: single-base valve: 0.01* rating Kvdouble-base valve, sleeve valve: 0.5%* rating Kv
    Differential pressure Mpa 6.4 4.0 4.0 4.0 3.5 2.3 2.0 1.42 1.4 0.91 0.55 0.35 0.26 0.17
    Match introduced actuator specification A+Z64
    Differential pressure Mpa 6.4 6.4 4.0 4.0 3.7 2.5 2.2 1.6 1.5 1.0 0.6 0.4 0.3 0.2
    Rated travel mm 10 16 25 40 40
    Flux characteristic Equal percentage Beeline
    Function style Volt on  Volt off
   Temperature range Normal temperature: -20 — +200 degree abstraction of heat: -60 — +450 degree
3. Manual Wafer Butterfly Valve Images：
 

4.Manual Wafer Butterfly Valve  Specification：
Size: DN50-DN1000
Seat: NBR/Hypalon/EPDM/Neoprene/NR/Wear-Resistant EPDM/Viton/Silicon/Heat-Resistant EPDM/White EPDM/EPDM(NSF)/PTFE
Suitable temperature: -10~120
Medium: Fresh water, sewage, sea water, air, vapor, food, medicine, oils, alkalis, salt etc.
 Nominal Pressure:   PN10/PN16
Working Temperature : -45 C centigrade-+200C centigrade
Suitable Mediums :  Fresh water, Sewage, Sea water, Air, Oils, Acids, Alkalis, Salts, etc. 
5.FAQ
 1. What is manual wafer butterfly valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.
 
2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
 
3. What is the working principle of manual wafer butterfly valve?
 A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.