Loading Port:China Main Port
Payment Terms:TT OR LC
Min Order Qty:-
Supply Capability:-
General Introduction
u This cutter suction dredger is designed to operate in sheltered inshore waters and under tropical climate conditions. Build under enterprise standard.
u The whole dredger is dismountable in road transportable sections.
u The engines and dredge pump are located in the center pontoon, the 2 side pontoons serve as fuel bunkers, ballast tanks and store.
u Engine room and pump section are accessible by watertight hatches
u Cutter shaft runs on roller type bearings in an enclosed shaft housing flooded with lubrication oil a lock oil tank to ensure a positive pressure inside the bearing housing is located on top of the wheelhouse.
u The spacious control cabin is ergonomically designed fitted on a raised platform with all around non obstructed view ,2 operators consoles containing engine instrumentation and controls for winches, dredge pump, suction and discharge pressure gauges, navigation light controls, airconditioned and well insulated .
u Below the control cabin is a changing room located with table, chairs and washbasin
u The underwater section of the dredger is protected with a marine coating system and cathodic protection for use in a saltwater environment。
TECHNICAL SPECIFICATION YS-CSD200P | ||||
No. | Item | Description | Remark | |
1. | General Principle |
|
| |
| (1). Overall Length | 22m |
| |
(2). Side Pontoon Size | 14m |
| ||
(3). Main Pontoon Size | 10.0m |
| ||
(4). Breadth | 4.6m |
| ||
(5). Moulded Depth | 1.6m |
| ||
(6). Mean Draft | 1.0m |
| ||
(7). Dredging Depth | 8m |
| ||
(8). Pumping Distance | 1000m |
| ||
(9). Pump Flow Capacity | 800m³/h |
| ||
(10).Suction Pipe Dia | 300mm | Out Diameter | ||
(11) Discharge Pipe Dia | 300mm | Out Diameter | ||
|
|
| ||
2. | Main Pontoon |
|
| |
| (1). Dimension | 10m*2.2m*1.6m |
| |
(2). Bottom Plate Thick | 8mm | |||
(3). Side Wall Thick | 6mm | CCSB marine plate | ||
(4). Front and Rear | 14mm | CCSB marine plate | ||
|
|
| ||
3. | Side Pontoon |
|
| |
| (1). Dimension | 14m*1.2m*1.6m |
| |
(2). Bottom Plate Thick | 8mm |
| ||
(3). Side Wall Thick | 6mm |
| ||
(4). Front and Rear Thick | 6mm |
| ||
|
|
| ||
4. | Main Engine |
| Drive dredger pump only | |
| (1). Make | WEICHAI |
| |
(2). Model | 6160 | Marine Engine | ||
(3). Power / rpm | 300 Kw @ 1000rmp |
| ||
(4). Fuel Consumption | 40L/h |
| ||
(5). Cooling Style | Water Cooling |
| ||
|
|
|
| |
6. | Axle Generator |
|
| |
| Make | STANFORD |
| |
Power / rpm | 24Kw |
| ||
|
|
| ||
7. | Harbor Generator |
| Drive hydraulic pump & axle generator | |
| Make | WEICHAI +STANFORD |
| |
Power / rpm | 24Kw |
| ||
Fuel Consumption | 4L/h |
| ||
Cooling Style | Air Cooling |
| ||
Output Voltage | 220V/ 380V |
| ||
|
|
| ||
8. | Dredge Pump |
|
| |
| Make | SHIJIAZHUANG |
| |
Model | 200G-G |
| ||
Suction Pipe Diameter | 250mm |
| ||
Discharge Pipe Diameter | 200mm |
| ||
Head | 65m |
| ||
Rpm | 1000rpm |
| ||
Water Flow Capacity | 800m³/h |
| ||
|
|
| ||
9. | Gearbox |
|
| |
| Model | FDL-320 |
| |
Ratio | 1: 1 |
| ||
|
|
| ||
10. | Cutter |
|
| |
| Style | Hydraulic Motor+ Planetary Gearbox | ||
Cutter Power | 55kw |
| ||
Crown Diameter | 900mm |
| ||
Cutter Out Diameter | 1000mm |
| ||
Blades | 5pcs | High manganese alloy | ||
Cutter Teeth | 28pcs | High manganese alloy | ||
Rpm | 0-10-30rpm |
| ||
|
|
| ||
11. | Ladder Winch |
| Hydraulic Drive | |
| Winch Motor Brand | NINGBO XULI |
| |
First Layer Pull | 4 Ton |
| ||
Wire Rope Dia | 16mm |
| ||
Wire Rope Capacity | 120m |
| ||
Wire Speed | 0-20m/min |
| ||
|
|
| ||
12. | Swing Winch |
| Hydraulic Drive | |
| Winch Motor Brand | NINGBO XULI |
| |
First Layer Pull | 4 Ton |
| ||
Wire Rope Dia | 18mm |
| ||
Wire Rope Capacity | 120m |
| ||
Wire Speed | 0-20m/min |
| ||
Quantity | 2 sets |
| ||
|
|
| ||
14 | Spud |
|
| |
| Length | 12m |
| |
Diameter | 325mm |
| ||
Weight | 2200Kg | Each | ||
| ||||
15 | Spud Cylinder |
|
| |
| Cylinder Stroke | 2.0m |
| |
Cylinder Dia | 125mm |
| ||
Working Pressure | 16Mpa |
| ||
Travel Speed | 0.2m/s |
| ||
| ||||
17. | Anchor |
|
| |
| (1). Type | HHP Anchor |
| |
(2). Weight | 200Kg |
| ||
| ||||
18. | Operation Cabin |
|
| |
| (1). Operation Board | Control all dredger movement commands and monitor equipments running condition. PLC system from SIMENS | ||
(2). Adjustable Chair | For dredger master. Leather. |
| ||
(3). A/ C | One set |
| ||
| ||||
19. | Hydraulic System |
|
| |
| A. System Introduction | Hydraulic system is designed to supply power for winches, cutter, spud cylinder. Hydraulic pump separately is driven by engine free end.
| ||
B. Hydraulic Motor | From YINING which is Italy-China Joint Venture Brand Excellent performance and usage life. | |||
C. Hydraulic Pump | NANJING | |||
| ||||
20. | Painting Principle |
|
| |
|
Introduction | Do sand blasting before welding. Use good quality marine paint with greater thickness. Paint system is 3 or 4 layers with minimum thickness of 400 micron on the below water line area. Fix anti-rust device inside and outside of pontoons. | ||
| ||||
19. | Electrical System |
|
| |
|
Introduction | All electrical components are from famous brand as Omron and CHINT. Equip overload protection box to control safety. Use high quality electrical marine type cables (smoke and halogen free). | ||
20. | Navigation Tool |
|
| |
| (1). Elec-mag Compass | Equipped |
| |
(2). VHF-Radiotelephone | Equipped |
| ||
|
| |||
21 | Optional Equipments |
| ||
(1) Pump Booster | Increase pumping distance | |||
(2) Spud Carrier | Stroke-4meter | |||
(3) Concentration Meter |
| |||
(4)Flow Capacity Meter |
| |||
| Pipeline |
| ||
(1). HDPE pipe | ID-285mm OD-315mm Thickness-15mm Length-11.5m/pcs | |||
(2). Rubber Hose | ID-300mm Length-1.2m | |||
(3). Floater | ID-315mm Length-1100mm OD-1100mm | |||
*Quantity depends on real pumping distance* | ||||
